Hydro Jetting in Girard

Hillside housing above the river

Girard was a mill town, and its oldest streets run up from the Mahoning River and the old steel works along Route 422. The houses downtown and on the first rise of hills, around Liberty Street, Churchill Road, and the blocks near the high school, date from the 1890s through the 1930s. The ranches and split-levels on the ridges toward Liberty Township were built through the 1950s and 1960s. Nearly every lateral is vitrified clay in short jointed lengths, running downhill from a cast-iron house drain to a main in the street. Some postwar blocks have Orangeburg. PVC is limited to replacements and a few newer streets.

The slope defines the plumbing here. A lateral that drops ten or fifteen feet between the house and the main carries flow fast, which keeps it cleaner than a flat line but puts the joints under tension as the ground moves.

Creep, frost, and roots on the slopes

The soil on Girard's hills is glacial till over shale, heavy with clay, and it creeps downhill a little every year. A jointed clay pipe laid down that slope stretches at the joints over decades, and the camera finds gaps where the bells have pulled apart rather than offsets. On the flatter ground near the river, the usual swelling and shrinking of wet clay does the damage, and frost to roughly three feet heaves the run closest to the house each winter.

Sycamores and silver maples line the older streets, and their roots follow the moisture from an open joint straight into the pipe. On a hillside lateral the first joints below the house are often the worst, because frost and creep both act there. Girard's older sewers carry some storm water, and in a heavy rain the mains in the low part of town near the river can surcharge into basements with floor drains and no backwater valve. The hillside homes rarely see that; their problem is the blocked or broken lateral itself.

Lining a sloped lateral, or bursting it

Cured-in-place lining handles most Girard laterals. The installer hydro jets the line, cuts the roots, and inverts an epoxy-saturated felt liner from the basement cleanout, curing it with hot water, steam, or UV. The liner bridges the small gaps at pulled joints, seals every bell, and keeps the roots out, and it does all of that without a pit on the hillside. For one pulled joint in an otherwise sound run, a sectional point repair cured over that joint is quicker and cheaper than lining the full length.

Pipe bursting is needed when a joint has separated so far that soil is visible, when a section has collapsed, or when an offset stops the camera. A bursting head is pulled from a pit near the main to a pit at the house, breaking the old clay while fused HDPE follows. On a slope the pits need shoring and a plan for groundwater and runoff, and the installer should walk the route with you before quoting.

Girard permits and the right-of-way

Girard issues the permit for lateral work and inspects it, reviewing the pre- and post-cure video for a liner or the open connection before backfill for a bursting job. Any work in the tree lawn, sidewalk, or street needs a right-of-way permit through the city. The city's sewer-use rules apply to connections, including the prohibition on downspouts, sump pumps, and footer drains in the sanitary lateral where sewers are separated. Homes just over the line in Liberty Township on county sewers fall under the Trumbull County Sanitary Engineer instead.

In most communities the owner's responsibility runs to the main. Ask the installer to confirm the connection point for your street and to include the permit and inspection in the quote.

What the day brings and how to compare installers

A lining crew sets up at the basement cleanout, jets and films the line, wets out the liner, inverts it, and cures it over a few hours. Branch lines are reinstated with a robotic cutter and the finished pipe is filmed. Drains are back by late afternoon. A bursting crew brings an excavator, shoring, and a pulling rig, and returns the next day to backfill, compact, and restore the slope.

Ask each bidder to point out the pulled joints on the footage and explain why their method fits. The scope should list footage, liner thickness or HDPE size, pit locations if any, and the warranty. To compare installers whose training and insurance have been verified, find a verified CIPP contractor and ask for a reference from a hillside job in Girard or nearby. A crew that has shored a pit on one of these slopes will have a plan for yours.

Hydro Jetting in Girard

What a jetter does that a cable cannot

A hydro jetter pushes water through a nozzle at several thousand PSI. Rear-facing jets pull the hose down the line and scour everything off the pipe wall: roots, grease, sludge, mineral scale, and the rust flakes inside old cast iron. A cable machine drills a hole through the blockage and leaves the rest on the wall, which is why cabled lines re-clog on a schedule.

Where it fits in a repair

Jetting is step one before lining, because a liner has to bond to clean pipe, and step one before an honest camera inspection, because a line full of roots or scale hides its own condition. It is also legitimate maintenance on its own for a structurally sound line that roots keep finding.

When a line should not be jetted

Cast iron that is paper-thin at the bottom can be opened up by an aggressive descaling pass. A collapsed clay section will not let the hose through. Orangeburg can delaminate under pressure. An experienced operator checks the line first, matches the nozzle to the material, and stops if the pipe is not holding up.

Maintenance versus repair

If the camera shows sound pipe, annual or semiannual jetting is a cheap way to stay ahead of roots. If it shows open joints, channeled cast iron or offsets, jetting is a stopgap and the money is better spent on lining, which removes the joints the roots are using.

ZIP codes served in Girard

Hydro Jetting is available throughout Girard, including ZIP codes 44420.

More trenchless services in Girard

Questions we hear in Girard